Delfield SSR2-SH Manual de instalación descargar pdf (Pagina 10)

Supremacy Series

Reach-Ins Service and Installation Manual

For customer service, call (800) 733-8829 or (800) 723-8948, Fax (989) 773-3210, www.deleld.com

Supremacy Series

Reach-Ins Service and Installation Manual

For customer service, call (800) 733-8829 or (800) 723-8948, Fax (989) 773-3210, www.deleld.com

Cleaning solutions need to be alkaline based or non-chloride cleaners.

Any cleaner containing chlorides will damage the protective lm of

the stainless steel. Chlorides are also commonly found in hard water,

salts, and household and industrial cleaners. If cleaners containing

chlorides are used be sure to rinse repeatedly and dry thoroughly

upon completion.

Routine cleaning of stainless steel can be done with soap and water.

Extreme stains or grease should be cleaned with a non-abrasive

cleaner and plastic scrub pad. It is always good to rub with the grain

of the steel. There are also stainless steel cleaners available which

can restore and preserve the nish of the steels protective layer.

Early signs of stainless steel breakdown can consist of small pits and

cracks. If this has begun, clean thoroughly and start to apply stainless

steel cleaners in attempt to restore the passivity of the steel.

Never use an acid based cleaning solution! Many food products

have an acidic content which can deteriorate the nish. Be sure to

clean the stainless steel surfaces of ALL food products. Common

items include, tomatoes, peppers and other vegetables.

The thermostat also has an OFF position that disconnects power to

the condensing unit, keep in mind the evaporator fans and lights will

still have power while the thermostat is in the OFF position. On freezer

units, the lights and defrost timer will still have power as well as the

condensate heating elements. During normal operation the freezer

temp is preset at approximately O˚F and the refrigerator is preset at

approximately 37˚F.

1. Turn the main power switch, located on the top of the control box

to the ON position. Turn the night position switch, on front of the

control box, to the ON position.

2. Adjust the temperature control to the desired temperature.

The green area on the scale represents the optimum food holding

temperature zone of 150°F to 170°F (66°C to 77°C). When the cabinet

is warmed up and the temperature stabilized, the cabinet temperature

will normally stay within a few degrees of the temperature control

set point. The display shows a precise measurement of the actual air

temperature within the cabinet, not an average reading. Therefore, it

is not unusual to see the temperature vary when the doors are opened.

The quick response of the heating system combined with the precision

temperature readings provide very accurate control of the cabinet

temperature.

3. The light switch (on the glass door models only) controls the

display lights inside the cabinet.

The unit is now operating and the display will continually show the

current interior cabinet temperature. The night power switch on the

front of the control body should be used to turn the unit off at night.

There is a ve minute delay to allow fans to remove heat before the

unit shuts down. This removes latent heat from the heated module

preventing high limit lock out. If desired, the main power switch can be

turned to the off position once the fan has turned off.

The cabinet interior is very hot! Avoid direct contact

with skin; use appropriate protective apparel, such as

gloves. The area near the heating duct will be hotter

than the rest of the cabinet. Never operate the unit

without the duct in place. Use only containers and

materials suitable for high temperature applications.

Never store combustible materials near the heating

appliance.

Removal of the Heated Module

1. Disconnect power.

2. Disconnect power harness.

3. Remove module from unit.

OPERATION INFORMATION

OPERATION INFORMATION (HEATED MODELS)

Stainless Steel Care and Cleaning

To prevent discoloration of rust on stainless steel several important

steps need to be taken. First, we need to understand the properties of

stainless steel. Stainless steel contains 70-80% iron which will rust.

It also contains 12-30% chromium which forms an invisible passive

lm over the steels surface which acts as a shield against corrosion.

As long as the protective layer is intact, the metal is still stainless. If

the lm is broken or contaminated, outside elements can begin to

breakdown the steel and begin to form rust or discoloration.

Proper cleaning of stainless steel requires soft cloths or plastic

souring pads.

NEVER USE STEEL PADS, WIRE BRUSHES OR

SCRAPERS!

MAINTENANCE

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 27 28

Comentarios a estos manuales

Sin comentarios

Delfield SSR2-SH Manual de instalación Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Neveras Delfield SSR2-SH